Connecting Powerwall to Wi-Fi

Connecting to Wi-Fi provides your Powerwall with a more stable connection to Tesla. With the Tesla app, you can configure the Wi-Fi settings of your Powerwall system. You can also update your network settings if you change your router or update your network connection. Your Powerwall is supported on 2.4 GHz networks with WEP/WPA1/WPA2 personal security as well as hidden SSIDs.

There are two methods for your Gateway to connect to or update your Powerwall’s Wi-Fi connection. The app will automatically select the connection method depending on your Powerwall’s internet connectivity.

If Powerwall is Disconnected from the Internet

Your Powerwall will always attempt to maintain an internet connection. However, it may disconnect from the internet if your Wi-Fi network has changed or if the local cellular network has gone offline. When your Powerwall is completely offline, a ‘Device Offline’ banner will be visible on the home screen, and recent power flow or energy data will not be visible. To configure Wi-Fi, go near your Powerwall and Gateway, and follow the steps below.

For Gateway 1 and Gateway 2

  1. In the Tesla app, locate your home energy site.
  2. Select ‘Settings.’
  3. Select ‘Configure Wi-Fi’ at the bottom of the screen.
  4. Complete the following in-app steps based on your product configuration.
    • For Gateway 1, click 'Manually Enter Details' and use the serial number from your Tesla app as the password (ex. STG1…<serial>).
    • For Gateway 2, scan the QR code located behind the glass door. 
  5. If the connection fails, reset your Gateway, wait five minutes and try again. You must stand next to your system during the entire setup.
    • To reset Gateway 1, press the reset button behind the metal door for approximately one second.
    • To reset Gateway 2, press the reset button behind the glass door for approximately one second.
    • Refer to your Owner’s Manual for instructions on how to reset Powerwall. If you are unable to reset your Powerwall, contact the Customer Support team.
  6.  ​​​​​​​Accept the request to join your Powerwall's local ‘TEG-xxx’ Wi-Fi network, where ‘xxx’ are the last three alphanumeric characters of your Powerwall serial number. Wait a few minutes for your phone to connect to Wi-Fi.
  7. Select your home Wi-Fi network, and then enter your network password.
    Note: Powerwall is supported on 2.4 GHz networks. 5 GHz networks are not supported.
  8. Tap ‘Connect’ to connect your Powerwall to Wi-Fi. The connection may take up to five minutes to complete.

For Powerwall 3

  1. On the energy home screen in the Tesla app, tap ‘Device Offline.’
  2. Select ‘Powerwall 3.’
  3. Open the toggle switch cover on your Powerwall 3.
  4. After two seconds, ‘Found Toggle Switch’ should appear as a prompt on your screen. Select this prompt once you locate the switch.
  5. When requested, tap ‘Pair’ to enable a Bluetooth connection between your phone and your Powerwall 3. 
  6. After you’ve paired your phone, toggle your Powerwall 3 switch off and then, back on.  
  7. Tap ‘Toggled Switch.’ 
  8. Accept connection to network when requested in the Tesla app. 

Note: Once connected to your home Wi-Fi, your Powerwall’s power flow and energy data will begin syncing with the Tesla network. If your device does not begin reporting data within 24 hours of connecting to Wi-Fi, contact contact the Customer Support team.

If Powerwall is Connected to the Internet Through Cellular or Wired Ethernet

If your Powerwall is actively connected to the internet through cellular or wired ethernet, follow the steps below to configure Wi-Fi without having to be near your Powerwall or Gateway.

To Connect Your Powerwall to Wi-Fi for the First Time

  1. In the Tesla app, locate your home energy site.
  2. Select ‘Network Setup.’
  3. Select your preferred Wi-Fi network.
  4. Enter your Wi-Fi network password.
  5. Your Powerwall is officially connected to Wi-Fi once you see a confirmation message on the screen.

To Change Your Existing Wi-Fi Connection

  1. In the Tesla app, locate your home energy site.
  2. Select 'Settings.’
  3. Select ‘Configure Wi-Fi’ at the bottom of the screen.
  4. Select the Wi-Fi network you would like your Powerwall connected to.

If You Do Not Want to Connect Your Powerwall to Wi-Fi

  1. In the Tesla app, locate your home energy site.
  2. Select ‘Network Setup.’
  3. Select ‘I don’t have a home Wi-Fi network.’

Note: You can connect your Powerwall to a Wi-Fi network at any time in the future by going to the ‘Settings’ page located on the Tesla app home screen.

Troubleshooting

If the connection to the Powerwall Wi-Fi network fails, reset your Gateway or Powerwall, wait five minutes and try again.

A Wi-Fi signal strength between two or three bars is required for successful connection to your home network. If a signal strength of two or three bars is not achieved, relocate your access point.