Windshield Wiper Blades, Jets and Fluid

Topping Up Windshield Washer Fluid

The only reservoir into which you can add fluid is the windshield washer fluid reservoir, which is located behind the front trunk. When the level is low, a message displays on the touchscreen.

To top up the washer fluid:

  1. Open the hood.
  2. Clean around the filler cap before opening it to prevent dirt from entering the reservoir.
  3. Open the filler cap.
  4. While avoiding spilling, fill the reservoir until the fluid level is visible just below the filler neck. The reservoir has a capacity of 4.5 liters.
    Filler cap with a zoombox showing target fill amount.
  5. Wipe up any spills immediately and wash the affected area with water.
  6. Reinstall the filler cap.
Informational PurposesAn informational icon, calling your attention
Note
Some national or local regulations restrict the use of Volatile Organic Compounds (VOCs). VOCs are commonly used as antifreeze in washer fluid. Use a washer fluid with limited VOC content only if it provides adequate freeze resistance for all climates in which you drive Model Y.
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
Use only ethanol-based windshield washer fluid meant for automotive vehicles. Using other substances, such as untreated water, can result in bacterial growth within the climate control system resulting in odor or potential damage that is not covered by warranty.
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
Do not add formulated washer fluids that contain water repellent or bug wash. These fluids can cause streaking, smearing, and squeaking or other noises.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
In temperatures below 4° C, use a washer fluid with antifreeze. In cold weather, using a washer fluid without antifreeze can impair visibility through the windshield.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Windshield washer fluid can irritate eyes and skin. Read and observe the instructions provided by the washer fluid manufacturer.

Checking and Cleaning Wiper Blades

Periodically clean the edge of the wiper blades and check the rubber for cracks, splits, and roughness. If damaged, replace the blade immediately to prevent damage to the glass and improve visibility.

Contaminants on the windshield, or on the wiper blades, can reduce the effectiveness of the wipers. Contaminants include ice, wax spray from car washes, washer fluid with bug and/or water repellent, bird droppings, tree sap, and other organic substances.

Follow these guidelines for cleaning:

  • Clean the windshield and wiper blades using washer fluid, isopropyl (rubbing) alcohol, or non-abrasive glass cleaner approved for use on automotive glass and rubber. Inappropriate products can cause damage or smears, and create glare on the windshield.
  • Lift the wiper arm a short distance away from the windshield, just far enough to access the wiper blade. Do not lift a wiper arm beyond its intended position.

If the wipers remain ineffective after cleaning, replace the wiper blades.

Replacing Wiper Blades

For optimum performance, replace the wiper blades at least once a year. Replacement blades must meet the following criteria:
  • The blade on the driver's side must be 650 mm long and 500 mm long for the blade on the passenger's side.
  • Ensure the connector on the replacement blade is the same as the original blade. Different connectors may prevent the replacement blade from connecting to the wiper arm on the vehicle.

You can purchase replacement wiper blades on the Tesla Shop.

Informational PurposesAn informational icon, calling your attention
Note
Only install replacement blades that are identical to the original blades. Using inappropriate blades can damage the wiper system and windshield.
To replace the wiper blades:
  1. Shift into Park and turn off the wipers.
  2. Touch Controls > Service > Wiper Service Mode to move the wipers to the service position.
  3. Lift the wiper arm a short distance away from the windshield, just far enough to access the wiper blade.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Wiper blades do not lock into a lifted position. Do not lift a wiper arm beyond its intended position.
  4. Place a towel between the wiper arm and windshield to avoid scratching or cracking the windshield.
  5. Hold the wiper arm and press the locking tab while sliding the blade down the arm.
    Zoombox of the wiper blade with an arrow pointing at the tab and another arrow indicating to pull apart
  6. Align the new wiper blade on the wiper arm and slide it toward the end of the wiper arm until it locks into place.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Ensure the new blade is locked in place and does not move. Perform a push-pull test to confirm. If not locked in place (you can hear and feel a "click"), the wiper blade may come off during use, resulting in serious damage.
  7. Turn Wiper Service Mode off to return the wipers to their normal position.

Cleaning Washer Jets

If a windshield washer jet becomes blocked, use a thin strand of wire to clear any blockages from the nozzles.

Zoombox with washer jets pointing to the underside of the washer blade
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Do not operate the washers while cleaning Model Y. Windshield washer fluid can irritate eyes and skin. Read and observe the washer fluid manufacturer’s instructions.