Parts and Accessories

Parts, Accessories, and Modifications

Use only genuine Tesla parts and accessories. Tesla performs rigorous testing on parts to ensure their suitability, safety, and reliability. Purchase these parts from Tesla, where they are professionally installed and where you can receive expert advice about modifications to Model 3. Accessories are available for purchase from Tesla stores or online at www.tesla.cn.

Informational PurposesAn informational icon, calling your attention
Note
Some accessories may not be available in your market region.

Tesla is unable to assess parts manufactured by other distributors and therefore accepts no responsibility if you use non-Tesla parts on Model 3.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Installing non-approved parts and accessories, or performing non-approved modifications, can affect the performance of Model 3 and the safety of its occupants. Any damage caused by using or installing non-approved parts, or by performing non-approved modifications, is not covered by the warranty.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Tesla does not accept liability for death, personal injury or damage that occurs if you use or install non-approved accessories or make non-approved modifications.

Body Repairs

If your Model 3 is in a collision, contact Tesla or a Tesla-approved Body Shop to ensure that it is repaired with genuine Tesla parts. Tesla has selected and approved body shops that meet strict requirements for training, equipment, quality, and customer satisfaction.

Some repair shops and insurance companies might suggest using non-original equipment or salvaged parts to save money. However, these parts do not meet Tesla's high standards for quality, fit and corrosion resistance. In addition, non-original equipment and salvaged parts (and any damage or failures they might cause) are not covered by the warranty.

Replacing Cabin Filters

Informational PurposesAn informational icon, calling your attention
Note
Depending on your vehicle's date of manufacture, screw may be in a slightly different location on the cabin filter cover.

Model 3 has air filters that prevent pollen, industrial fallout, road dust, and other particles from entering the cabin through the vents. Tesla recommends replacing these filters every 2 years (every year in China). Cabin filters can be purchased at the Tesla Shop.

To replace the cabin filters:

  1. Turn off the climate control system.
  2. Move the front passenger seat fully rearwards and remove the front passenger floor mat.
  3. Use a clip pry tool to carefully release the push clips that secure the front passenger footwell cover to the instrument panel. Then, while supporting the footwell cover, disconnect the two electrical connectors and move the footwell cover aside.
    • For the light, carefully press down on the tab while releasing the connector.
    • For the speaker, carefully angle the vehicle-side connector so that the small tab releases from the hole in the footwell cover-side connector while releasing the connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    To avoid damage, do not pull on the wires when disconnecting the connectors. When disconnecting the connectors, make sure to pull from the plastic on the connectors themselves.
  4. Working from top-to-bottom, use a trim tool to carefully release the right side panel from the center console.
  5. Remove the T20 screw that secures the cabin filter cover to the heating, ventilation, and air conditioning (HVAC) module, then release the cabin filter cover and move it aside. On some vehicles, the screw is a T20/6mm hybrid fastener. Locking tabs may also replace the screw: use your index finger and thumb to squeeze the two tabs at the bottom of the cabin filter cover. Tilt the cover outward to remove.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the HVAC module does not have a cabin filter cover, reinstall the trim panels and contact Tesla.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Do not stretch, bend, or otherwise damage the orange High Voltage (HV) cables that are attached to the cabin filter cover. If the HV cables are damaged, immediately discontinue this procedure. HV shock can result in serious injury or death.
  6. Fold the upper cabin filter’s tab upward and the lower filter’s tab downward.
  7. Holding the tab on the upper cabin filter, pull the upper filter out from the HVAC module.
  8. Holding the tab on the lower cabin filter, pull the lower filter upwards and then out from the HVAC module.
  9. Ensuring that the arrows on both new filters face towards the rear of the vehicle, insert the lower cabin filter into the HVAC module and lower it into place. Then, insert the upper cabin filter above it.
  10. Fold the tabs inward so that the cabin filter cover can be installed.
  11. Install the cabin filter cover by engaging the lower cover tab then securing the T20 screw or T20/6mm hybrid fastener. Tighten the screw to 1.2 Nm/0.89 ft-lbs. On vehicles with tabs instead of a T20 screw: maneuver the top notch of the cabin filter cover into place, then secure the tabs at the bottom of the HVAC module.
  12. Reconnect the two electrical connectors to the components in the front passenger footwell cover, then resecure the cover with the push clips.
  13. Align the right side panel with the front and rear locator slots on the center console, then apply pressure until all of the clips are fully secure.
  14. Reinstall the front passenger floor mat then move the front passenger seat back into place.

Using RFID Transponders

When attaching an RFID transponder (used by many automated toll systems) inside Model 3, place the transponder next to the rear view mirror. This ensures best results and minimizes any obstruction to your driving view. Refer to the RFID manufacturer's instructions for specific placement.

Informational PurposesAn informational icon, calling your attention
Note
You can also attach a weather-proof transponder to the front license plate.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
When attaching a tag to the windshield, you must ensure that it does not obstruct the driver's vision. Failure to do do could result in serious injury and/or death.